The Mustang E13 is a track mounted multipurpose drill rig
which is highly effective on reverse circulation and diamond
drilling especially when RC to DD switching time under
consideration. At the time compared with other RC rigs its compact
sizes allow to reach to hardest locations with 13 tons pull back and
13 tons torque capacity. This powerful drilling capacity also gives
efficiency on water and geotechnical drilling even for piling.
Our Mustang 13 rigs are working
together with track mounted XRVS 476 (365 psi / 962 cfm ) and XRXS
566 ( 435 psi / 1186 cfm ) compressors. Boosters and Dust Collectors
are available upon request.
Depth Capacity Coring (Wireline or Conventional)
N Wireline 1500 meter
H Wireline 1100 meter
P Wireline 700 meter
Reverse circulation down the hole hammer
4" rod - 350 meter
5" rod - 260 meter
Engine
Type
:
Deutz diesel BF6L 914
Cooling System
:
Air
Rated Power
:
165 hp
Torque
:
550Nm @ 2300 r/min
Cylindervolume
:
6.472 dm³
Number of Cyclinder
:
6
Canopy
:
Sound-proofing
Electrical System
Starter
:
4 kW/24V
Alternator
:
28V/32A
Battery
:
2 x 12 V,100Ah
Rotation Unit
Type
:
RH 130
Rotation Speed
:
8 gear, 0-655 r/min
Torque
:
1300 daNm
Feed System BMI 6,7
Length
:
6250 mm
Free Travel Lenght
:
6700 mm
Feed and Retract Force Max
:
130 kN
Travel Speed(Max.high speed)
:
53 cm/sec
Travel Speed(Max.low speed)
:
27 cm/sec
Crawler
Crawler Track Lenght
:
2500 mm
Crawler Track Total Lenght
:
3715 mm
Track Width
:
400 mm
Speed on Level Ground
:
1,8 km/h
Climbing Angle
:
%57 (30°)
Dimensions
Lenght in Transport Position
:
11100 mm
Height in Transport Position
:
3320 mm
Width
:
2480 mm
Hydraulic System Basic Components
Hydraulic Pump(2)
:
For drill head rotation crawler track motors,
feed beam positioning,winch and rod holder
Type
:
Rexroth A 10V 071
Max.Pressure
:
280 bar
Hydraulic Pump(3)
:
Feed system
Type
:
A 10V 071
Max.Pressure
:
280 bar
Hydraulic Pump(4)
:
Gear pump intented for driving waterpumps
Type
:
Bosch ZFZ 11/11L
Max.Pressure Set for Foampump Operation
:
100 bar
Drill Rod Breaker/Holder & Guide
Max.Opening
:
300 mm.
Max.Grip force
:
125 kN
Rotate Swing Angle
:
18º
Winch
Pull Max.
:
30kN
Max.Speed
:
0,6 m/s
Wireline Hoist
Capacity Ø 6 mm Cable
:
1200 m
Capacity Ø 5 mm Cable
:
1450 m
Pull Max(empty drum)
:
5,8 kN
Max.Speed (empty to full drum)
:
3-5 m/s
Water Pump
Type
:
Trido 80
Discharge Capacity
:
75 l/ min
Max. Discharge Pressure)
:
40 bar
Standart Equipment
- Turntable
- Rod Rack ( 50 x 4" RC Rod 4,0 m.)
- 4 Hydraulic Jack
- Hydraulic Mast Dump
- Fuel Tank 120 l
- Hydraulic Mud Mixer
- Hydraulic Cooling System
- Cyclone
Weight
18000 kg
CS-14 DRILL RIG PERFORMANCE SPECIFICATIONS
As a latest technology product
the Christensen CS-14 is a long stroke hydrostatic surface diamond
core drill rig. It is mounted on tracks and can also carry 330 m
HQ/NQ drill string, accs. and spares together with additional fuel
and water tanks on its chassis. This rigging allows one week
drilling without logistical support.
Manufacturer : Atlas Copco Craelius Sweden,2006
Depth Capacity Coring (Wireline or Conventional)
B Wireline 1540 meter
N Wireline 1200 meter
H Wireline 800 meter
P Wireline 475 meter
Depth are based on vertical hole
Main Hoist
Single Line capacity
:
Bare Drum 80 kN
Line Speed
:
44 m/min
Cable Size
:
35 m x 16 mm.
Wireline
Capacity
:
1830 m of 5 mm
975 m of 6 mm
Line Pull
:
Bare drum : 11,9 kN
Full drum
:
3,0 kN
Line Speed
:
Bare drum 114 m/min
Full drum 453 m/min
Mast and Feet System
Feed Travel
:
3,5 m
Feed Speeds
:
Fast and slow with variable control
Thrust
:
59,6 kN
Pull
:
138 kN
Drilling Angle
:
45 to 90 degrees
Rod Pull Lenght
:
6,09 m
Power Unit
Manufacturer
:
Caterpillar
Model
:
CAT 6.6 6,6 liter 6 cylinder ,Tier III
Power
:
216 hp
RPM
:
1900
Engine Type
:
Type : Diesel turbocharged/after cooled
Cooling
:
Water
Hydraulic System
Primary Pump
:
28Mpa-242 l/min
Secondary Pump
:
20Mpa- 122 l/min
Auxiliary Pump
:
21,5 Mpa-47 l/min
Hydarulic Oil Cooling
:
Air
Drillhead and Spindle Speeds
Power : Hydraulic motor-variable speed/reversible
Final Drive : 4 in chain driven in oil bath-2,5 ratio
Spindle (inner diameter) : 117 mm
Spindle Speeds :
Ratio
Speed,rpm
Torque,nm
1 st 6,63 :1
117 - 196
5113 - 3051
2nd 3,17 :1
245 - 410
2445 - 1459
3rd 1,72 :1
451 - 756
1326 - 792
4th 1.00 :1
776 - 1300
771 - 460
Range Selection
:
Manual control from operator's station
Hinged Head
:
Swing away
Chuck Assembly
Type
:
Hydraulic open,spring closed
Max.Inside Diameter
:
117 mm
Holding Capacity
:
18143 kg
Driller Base Supports
Crawler mounted rig, fuel tank(2000 l), water tank(3000 l)
Support
:
4 hydraulic jacks
Weight
Crawler,tanks,CS-14 incl.Trido 140 and rod holder 20.000 kg.
Standart Equipment
- Hydraulic Mast Dump
- Mast Two Section
- Large Crown Sheave Wheel
- Wear Lines on Lower Mast
- Safety Guards
- Hydraulic Mast Raise
- 4 Hydraulic Levelling Jack
- Towing Package
- Fuel Tank
- Fuel Filter & Water Separator
- Hydraulic Oil Reservoir Fill Pump & Filtration
- Hydraulic P-sSize Rod Holder
- Hydraulic Mud Mixer
- Hydraulic Mud Pump,Trido 140
- Max Flow : 140 l/min
- Max Pressure : 7MPa
XRVS-476 COMPRESSOR PERFORMANCE SPECIFICATIONS
Manufacturer : Atlas Copco Belgium,2006
Engine Shaft Speed Normal an Maximum
Engine Shaft Speed,Compressor Unloaded
Free Air Delivery
Manufacturer
Model
Power
Cylinder
Nominal Effective Working Pressure
Maximum Effective Receiver Pressure,Unloaded
Minimum Effective Receiver Pressure
1600 r/min
1200 r/min
460 I/s
Caterpillar
C13 ATAAC
440 Hp
6
25 bar / 363 psi
27 bar / 392 psi
15,5 bar/ 225 psi
XRXS-566 COMPRESSOR PERFORMANCE SPECIFICATIONS
Manufacturer : Atlas Copco Belgium 2008
Engine Shaft Speed Normal an Maximum
Engine Shaft Speed,Compressor Unloaded
Free Air Delivery
Manufacturer
Model
Power
Cylinder
Nominal Effective Working Pressure
Maximum Effective Receiver Pressure,Unloaded
Minimum Effective Receiver Pressure
1800 r/min
1300 r/min
560 l/s
Caterpillar
C18 ATAAC
575 Hp
6
30 bar/ 435 psi
32 bar / 464 psi
19 bar / 276 psi
D-120 DRILL RIG PERFORMANCE SPECIFICATIONS
The D-120 is a track mounted , compact ,all hydraulic diamond core drill for surface exploration drilling. It can also carry 100 m HQ/NQ drill string , accessories and spares by itself for faster and efficient hole to hole moves
Depth Capacity
WL Diamond Coring
NQ - 800 m. / 2.624 ft.
HQ - 550 m. / 1.804 ft.
PQ - 200 m. / 656 ft.
